Clik here to view.
Clik here to view.
Amazon FireTV stick port protector
Bracket to keep the Amazon Basics microUSB cable (the one that comes with the stick) from tearing out the port in the FireTV stick.
View ArticleClik here to view.
Prusa i3 MK2: V2 holder clips for Y-axis' igus drylin RJZM-01-08 bushings
NOTE: Project was updated on November 3rd 2016 - Please read the project update notes below! I upgraded my Prusa i3 MK2 with linear bushings (and shafts) from igus. To be more specifically, the igus...
View ArticleClik here to view.
Prusa i3 MK2: V2 holder clips for Y-axis' bearings (LM8UU and igus drylin...
ATTENTION: Please read the project's update notes at the bottom of this page! I add to my effort to make the linear system of the Prusa i3 MK2 more stable, reliable and easier to adjust these clips for...
View ArticleClik here to view.
prusa i3 rework 1.5 alu frame brace for M10 threaded road
This is a frame brace for prusa i3 rework 1.5 with 10mm threaded row frame. You need to replace the original back threaded roads to a 30cm long one You need 4 pieces of M4x23mm screw + nut + washer 2...
View ArticleClik here to view.
GEEETech MK8 Printhead Fan Shroud ver.3 (compact)
A revised version of my GeeeTech Prusa i3 Acrylic print cooler duct that mounts to the MK8 Extruder - My MK8 extruder came with a cooling block that had the heat sink fins running in a vertical...
View ArticleClik here to view.
Wire stripper
Wire stripper. Not very beautiful (this is too big blade for this tool), but works well. All you need is M3 screw, M3 nut, and utility blade. UPDATE: Made version 2 - stronger and without useless...
View ArticleClik here to view.
Anet A6 & A8 Mosfet Holder
This holder is for the mosfet made by MKS. Remove the two lower screws and spacer under the mainboard and replace with your chosen mosfet holder. You will need 4 x M3x8 size screws to mount the mosfet....
View ArticleClik here to view.
Blower Ring for Anycubic3D Kossel Mini
This is a full ring blower duct for my Delta printer Anycubic3D mini Kossel. The code is messy, but it should be somewhat customizable and (hopefully) not complicated. UPDATE: The ring model is now a...
View ArticleClik here to view.
Fury X220 Racing Drone
Fury X220 Racing Drone Canopy The design of the canopy is an evolution of Emiel's canopy for the Realacc X210. Thanks Emiel! I improved the canopy to fit and protect a HS1177/HS1190 with GoPro 2 lens...
View ArticleClik here to view.
Knurled Tri-Spinner Fidget Widget / Triple Bearing Spinner
I love the tri-spinners and I have made them for many people. I just don't like having to use 4 608 bearings for each spinner with 3 of them just used as counterweights. I found that 1/2 inch nuts have...
View ArticleClik here to view.
OpenForge rowboats
OpenForge ========= 1, 2,& 3 person rowboats for your next RPG game on the highs seas! One of these is inspired by a rowboat in Paizo's Map Pack: Vehicles OpenForge Sets ============= Smooth Tile...
View ArticleClik here to view.
Fish Fossilz
Fish Fossilz are an amazing one piece print that wriggles, twists and bends in all directions. It's an easy print that only uses about 13gm of filament (with recommended settings). Fish Fossilz have...
View ArticleClik here to view.
Hypoid Gear Drive Model
https://youtu.be/tOvE46CIA80 This is a fully-functional finger-spun hypoid gear drive model. The hypoid gear drive is similar to the bevel gear drive, but the axes of the wheel and pinion in a hypoid...
View ArticleClik here to view.
Hollow Calibration Cube
This is a hollow 20mm cube for calibrating your 3D printer! Cubes are hugely popular to calibrate axis linear travel, but this hollow design also allows you to also calibrate bridging and extrusion...
View ArticleClik here to view.
Low Poly Elephant
I just figured out how to low poly-ize things! I love low poly things! EDIT: I've gotten an Instagram! Find me @spryde3d
View ArticleClik here to view.
Brilliant Cut Diamond Cleaned Up
If you like my work I hope you'll consider supporting me on Pateron: https://www.patreon.com/3DPrintingProfessor Subscribe to me on YouTube: https://www.youtube.com/user/mrjoesays The original...
View ArticleClik here to view.
The Universal Spool Holder - Main Page
This is the main page for my universal spool holder design... This page contains every single file I have made and every derivative of the holder... I'm going to lay out instructions on how to get the...
View ArticleClik here to view.
Qx90 2in1 landing pads / lipo holder
Qx90 landing pads + lipo holder. Replace weak stock pads and allow to get rid of rubber band.
View ArticleClik here to view.
Grado headphones bracket replacement part
This part was used to replace a broken bracket on my Grado headphones. It is the part that holds one of the speakers to the headband. It fits my Grado Labs Alessandro headphones perfectly.
View Article